Return to GEN II - C.A.M. Loader for All Pistol Mags 9mm/.40 caliber

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 5

0 of 0 people found the following review helpful:

Speed loader May 14, 2026 Reviewer: Ken Hayes from North Carolina   First received it 3 days early which was great! I applied oil to the slide areas as suggested but the cartridges bind near the intake area of the magazine. It’s getting better with use. Works great with my M&P double stack but my 1911 Mec-Gar clip will not even insert into the loader. I purchased this loader because it states that it will work well with any 9mm and 40 magazines. Was this review helpful to you?

0 of 0 people found the following review helpful:

Awesome, Awesome March 4, 2026 Reviewer: Tim from Independence, MO   I purchased the speed loader for my AR-15.  Awesome product and so easy to use.  Would 100 percent recommend to a friend. Was this review helpful to you?

3 of 3 people found the following review helpful:

Could not get to work with Canik 9mm magazines September 3, 2025 Reviewer: RICHARD BOWEN from Zanesville OH   I could not get this speed loader to work with Canik METE magazines. The overall construction is great and it works with my S&W and Glock mags but not my Canik Was this review helpful to you?

0 of 0 people found the following review helpful:

loader July 20, 2025 Reviewer: Tom from phoenix   Works great on my CZ 9mm mags  Needed to take some time and learn.  Had issues using and then backed up a little bit.  Start with 1 round, then 3, then 10.  Give a chance to break in and also learn technique.  Now I'm loading 18 rounds per mag in seconds.  Very nice Was this review helpful to you?

0 of 0 people found the following review helpful:

loader modification June 29, 2025 Reviewer: Phil from USA   How about making the opening into the magazine on the 9mm/.40SW a 1/4" taller to accept 10mm cartridges. My 10s fit the tongue but the opening is just a little short. My .45 loader accepts 10mm but the tongue is too wide. I works but not well. Thanks Was this review helpful to you?

0 of 0 people found the following review helpful:

Taurus mags March 7, 2025 Reviewer: Christopher E Latta from NC   I noticed that your video didn't mention taurus as one of the brands that your speed loader could be used with was that an oversight or does it not work for taurus mags? Was this review helpful to you?

2 of 2 people found the following review helpful:

Gen 2 9mm loader February 23, 2025 Reviewer: Gary from Florida   Works great for sig, walther and Glock mags, but it wouldn’t work on my Springfield prodigy mags Was this review helpful to you?

0 of 0 people found the following review helpful:

Love it, hoping for a GEN III February 8, 2025 Reviewer: Gerald from Beaverton OR   I have been using this for my Hellcat Pro, OG Shield 9 and Beretta mags with no issues. Really hoping a newer version that will support the 2011 mags comes out. Was this review helpful to you?

0 of 0 people found the following review helpful:

Time saver December 15, 2024 Reviewer: Phillip Lash from Bloomfield , IN United States   Works great just make sure you keep it lubed Was this review helpful to you?

0 of 0 people found the following review helpful:

Review November 12, 2024 Reviewer: David Grosz from Washington state   So I went out with high expectations with my new Gen II C.A.M. Loader and opened package and no instructions, thought that was odd but no worries watched videos so all good.  Picked up 10 rounds easy peasy, turned it over and nothing no rounds went in AT ALL!  So removed mag and shells and looking closer well DUH the instructions were inside where the mag goes so upon removing the instructions and tried again and 250 trouble free rounds later am perfectly happy with my purchase! Was this review helpful to you?